කලම්ප අත් සන්ධි එකලස් කිරීම
Assembly of sleeve type pipeසවිකෘත
Preinstallation the most important link of the preinstallation of the sleeve type pipeසවිකෘතමුද්රාවේ විශ්වසනීයත්වය සෘජුවම බලපායි. විශේෂ පූර්වගාමීන් සාමාන්යයෙන් අවශ්ය වේ.සවි කිරීමs with small diameter can be preassembled on the bench vice. The specific approach is to use aසවිකෘත අනුකෘතිය ලෙස, නට්, කලම්ප අත් පයිප්පයට තද කළ හැක. ප්රධාන වශයෙන් පයිප්ප හරහා අත් වර්ග තිබේසවිකෘත, සම්බන්ධක හිස හරහා අත් වර්ගයේ අවසානය, අත් වර්ගයේ තුන්-මාර්ග පයිප්පසවිකෘතand other types. The author found that even for a batch of goods from the same manufacturer, the depth of the conical hole on theසවිකෘත body is often not the same, resulting in leakage, and this problem is often ignored. The correct way is to use what kind ofසවිකෘත body is used at one end of the pipe, and the correspondingසවිකෘත අවසානය එකම වර්ගයේ පෙර ස්ථාපනය කර ඇත සවිකෘත, කාන්දුවීම් ගැටළු උපරිමයෙන් වළක්වා ගැනීම සඳහා.
පයිප්පයේ අවසාන මුහුණත සමතලා විය යුතුය. නළය කියත් කිරීමෙන් පසු එය ඇඹරුම් රෝදය සහ අනෙකුත් මෙවලම් මත ඒකාකාරව ඔප දැමිය යුතු අතර, භාවිතා කිරීමට පෙර බර්ස් ඉවත් කර පිරිසිදු කර ඉහළ පීඩන වාතයෙන් පිරිසිදු කළ යුතුය.
පූර්ව ස්ථාපනය අතරතුර, පයිප්පයේ කොක්සියුලය සහසවිකෘත body should be kept as far as possible. If the pipe is too deviation, it will also cause sealing failure.
The pre-installed force should not be too ambassador that the inner edge of the sleeve is just embedded in the outer wall of the pipe, and the sleeve should not be obvious deformation. When connecting pipes, assemble according to the specified tightening force. The clamping force of the 6-1 sleeve is 64-1 15N, 16ф MMR 259N, ф18mm for 450N. If the jacket deformation is serious in pre-installation, the sealing effect will be lost.
Do not add sealant and other fillers. Some people in order to achieve better sealing effect, in the card sleeve coated with sealant, the sealant was rushed into the hydraulic system, resulting in hydraulic components Yin nihole blockage and other faults.
When connecting the pipe, the pipe should have enough deformation allowance to avoid the pipe being subjected to tensile force.
When connecting the pipeline, it should avoid being subjected to lateral force, which will cause lax sealing if the lateral force is too large.
When connecting the pipeline, it should be good once and avoid multiple disassembly, otherwise it will make the sealing performance worse.
Installation of sleeve type pipe සවිකෘත
(1) 9 වන පරිච්ඡේදයේ අවශ්ය පයිප්ප අච්චාරු දැමීම මුලින්ම සිදු කළ යුතුය;
(2) කියත් යන්ත්රයක් හෝ විශේෂ පයිප්ප කැපුම් යන්ත්රයක් සහ වෙනත් මෙවලම් සමඟ අවශ්ය දිගට අනුව නළය කපන්න, නළය (දැල්ල කැපීම වැනි) හෝ ඇඹරුම් රෝද කැපීම විසුරුවා හැරීමට නියත වශයෙන්ම අවසර නැත; පයිප්ප අවසානය, ලෝහ චිප්ස් සහ අපිරිසිදුකම ඇතුළත සහ පිටත බර්සර් ඉවත් කරන්න; පයිප්පයේ මලකඩ විරෝධී නියෝජිතයා සහ අපිරිසිදුකම ඉවත් කරන්නසවිකෘත; ඒ සමගම පයිප්පයේ වටකුරු බව සහතික කිරීම සඳහා;
(3) ගෙඩිය, කමිසය පයිප්පයට සවි කර ඇත, කමිසයේ ඉදිරිපස දාරය (කුඩා කෙළවර) නල මුඛයෙන් අවම වශයෙන් 3mm, පසුව නළය තුළටසවිකෘත body cone hole, top until;
(4) ගෙඩිය සෙමින් තද කරන්න, එය චලනය නොවන තෙක් නළය හරවන්න, ඉන්පසු ගෙඩිය 2/3 සිට 4/3 දක්වා තද කරන්න;
(5) විවෘත කර ජැකට්ටුව පයිප්පයට කපා ඇත්ද යන්න සහ ස්ථානය නිවැරදි දැයි පරීක්ෂා කරන්න. ජැකට් අක්ෂීය චලනය වීමට ඉඩ නොදේ, නමුත් ටිකක් භ්රමණය;
(6) පරීක්ෂණය සමත් වූ පසු ගෙඩිය තද කරන්න.